Wood/Chuck W/C 12 Drum Chipper

WoodChuck WC12 ChipperW/C 12

GENERAL SPECIFICATIONS

Weight: 3,500 lbs.
Length: Transport 13' 6" / Operational 17' 6"
Width: 7' 3"
Height: 7' 3"
Noise Level: 80 decibels at 50 feet 360 degrees around the unit or less

CHASSIS FRAME

6" channel frame unitized designed for stability and handling. Crossmembers are coped and welded to form an interlocking connection for strength and longevity. Frame is epoxy-primed inside and out for complete rust protection.

AXLE

Heavy duty, 6,000-lb. torsion type axle, 5-year warranty. 6 lug pattern wheels are standard with greasable bearings.

FENDERS

One piece 11-gauge fender, bolted to frame for ease of replacement. Backing splashguard is standard.

BRAKES

Heavy-duty, self-adjusting electric brakes. Safety breakaway switch is standard.

TIRES

2.25 x 75R15, Load Range "D" radial tires mounted on heavy duty 6 lug wheels.

JACK STAND

Bolt on 7,000-lb. capacity. Drop leg with pin for safety and convenience. Stationary foot pad is standard.

SAFETY CHAINS

Two (2) 3/8" x 6' safety chains with grab hooks.

TOW BAR

26" sq. tube 14" x 3 12" x 3 12" with 2 '1/2" pintle ring (or 2" ball) face-mounted to a 1" thick plate adjustable for height. Telescoping tongue to allow for length adjustment.

FUEL TANK

Federally approved 26-gallon fuel tank, standard with lockable cap and padlock. Tank is rubber isolated at frame mounts to absorb shock.

LIGHTING

Heavy-duty taillight package conforms to all D.O.T. specifications. Brake/turn signals and clearance lights are hermetically sealed, shock mounted with grommets and flush mounted to frame for protection. License tag light and bracket mounted within steel plate for protection. Wiring protected in conduit for shielding at all strategic points. All connections soldered in wiring harness.

BATTERY BOX

Battery is enclosed with an all steel frame, frame-mounted box. The battery box is standard with padlock.

CUTTING SYSTEM ROTOR


11" diameter, solid 1018 steel forged rotor. The rotor is available in a 12" length. The rotor is precision-machined and faced on all surfaces to ensure a uniform balance.

ROTOR SHAFT

3" diameter, 1018 solid steel forged shaft.

BEARINGS


Greasable, four-bolt flange-type bearing with static misalignment capabilities. Two year warranty

CHIPPER KNIVES

Four (4) high-carbon cutting knives with serrated backs allowing quick blade changes and full-length interlocking support. Blades are 3/8" thick x 3" wide x 12" long.

FEED PLATE ANVIL


Hardened solid steel cutter bar. The cutter bar is adjustable and has four (4) usable cutting edges. The cutter bar is 3/4" thick x 3" wide x 12" long.

ROTOR HOUSING

The housing is constructed of 5/8" thick A-36 grade steel plate, welded and precision-machined to provide many years of service and durability.

FEED PLATE

Heavy-duty reinforced steel weldment designed to withstand heavy shock loads, to be quickly adjustable and easily replaceable in event of heavy wear.

FLYWHEEL

Machined from solid 1018 steel plate. 18" diameter x 4" thick. The flywheel is dynamically balanced to provide smooth flow for the blower system and stored energy backup for the rotor.

INFEED CHUTE SYSTEM

All steel heavy construction infeed chute is 42" in width, 27" in height and 33" in depth. The infeed chute is fitted with a folding feed table that is designed to position the operator to left or right of center while feeding the chipper.

FOLDING FEED TABLE

The folding feed table is 45" wide and 50" long. The folding feed table is designed to position the operator to the left or right of center while feeding the chipper. Overall length from the nip point of the rotor to the end of the folding feed table is 77".

DISCHARGE CHUTE

80" all steel round discharge chute designed to propel chips by centrifugal force. The discharge chute is adjustable for height and is fitted with a 16" chip deflector that can rotate 360 degrees for side discharge applications.