Mitts & Merrill Chippers

TRAILER UNITS

  • SERIES 120 (12" WIDE CUTTER HEAD)
Model Engine
Drive
Weight
Capacity
K12F6 Ford 4.2 Litre V6 Gas
Clutch
3480 lbs.
8" Dia. Logs
K12F6SC
Swivel Chute
Ford 4.2 Litre V6 Gas
Clutch
3600 lbs.
8" Dia. Logs
K12JD4D John Deere 4 cyl Diesel
Clutch
3820 lbs.
8" Dia. Logs
K12C4D Cummins No.4-B 4 cyl Diesel
Clutch
3845 lbs.
8" Dia. Logs
K12P4D Perkins No 4-236 4 cyl Diesel
Clutch
3790 lbs.
8" Dia. Logs

 

  • SERIES 160 (16" WIDE CUTTER HEAD)
Model Engine
Drive
Weight
Capacity
K16F6 Ford 4.2 Litre
V6 Gas
Clutch
3730 lbs.
8" Dia. Logs
K16JD4D John Deere
4 cyl Diesel
Clutch
4070 lbs.
8" Dia. Logs
K16C4D Cummins No.4-B
4 cyl Diesel
Clutch
4095 lbs.
8" Dia. Logs
K16P4D Perkins No 4-236
4 cyl Diesel
Clutch
4040 lbs.
8" Dia. Logs

Staggered knife pattern

A series of short knives spaced about the rotating cylinder provides a smooth cutting action and a small, marketable chip. The knives which are sharp on both sides (top & bottom) are quickly and easily accessible for reversal or sharpening by lifting the hinged cover.

Telescoping Discharge Chute

The chute is adjustable to various heights, and rotatable a combination that means dump boxes can be filled quickly from corner to corner with minimum spill. An adjustable bonnet at the end of the chute also permits discharge to either side, or forward.

STANDARD FEATURES

ALL. MODELS have 16" diameter solid steel Cutter Heads with attached air blowers.

Other standard features:

  • Safety-lock pins help prevent the accidental throw-out of knives not properly tightened.
  • Solid steel oversize cutterhead ( 16" diameter) & staggered knives make for smooth cutting
    & small marketable chips.
  • Integral rotor blower forces chips through discharge chute.
  • Double-edged knives provide twice the cutting time between sharpening.
  • Tilt type engine cover. Beveled fenders, chamber cover and engine cover.
  • Fenders, belt guard, motor cover all undercoated to prevent rust.
  • Easy loading is provided by the wide-angle feed chute which is free of obstructions.
  • Feed chute folds to enclose the cutter chamber during storage or transportation. It is side hinged so it may be swung away for easy access to cutter chamber.
  • Re-enforced steel frame with 6000 LBS. torsion spring rubber mounted axle to assure excellent
    roadability. Electric brakes with break-away switch.
  • Brakes and lights comply with Federal D.O.T. regulations, and both are wired to the front for truck hookup.
  • Battery and anti-freeze installed, ready to go to work.
  • Adjustable front jack stand with flat landing foot, plus rear support stand.
  • Necessary tools and manuals included.
  • Feed chute folds to enclose the cutter chamber during storage or transportation. It is side hinged so it may be swung to either side for easy access to cutter chamber.

NEW HYDRAULIC SELF FEEDING MITTS & MERRILL BRUSH CHIPPER

Model Engine
Drive
Weight
Capacity
KH16F6 Ford 4.2 Litre
V6 Gas
Clutch
4670 lbs.
6-8" Dia. Logs
KH16C4D

Cummins No.4-B 3.9P 4 cyl Diesel

Clutch
5035 lbs.
6-8" Dia. Logs
KH16P4Dtb Perkins No 4-236
4 cyl Diesel w/ turbo
Clutch
4980 lbs.
6-8" Dia. Logs
KH16J4D John Deere
#5030HII99
4 cyl Diesel
Clutch
5010 lbs.
6-8" Dia. Logs

Standard Features:Mitts & Merrill Chipper

  • 16" Wide by 16" Diameter solid steel drum (drum alone weighs 950 lbs.) with 12 double edge knives in staggered pattern.  Produces small, fine chip - excellent for mulch.
  • 10 ½" dia. x 22 ½" wide feed roller -  Compacts brush, leaves, vines and hedge trimmings. No dead area between roller and cutterhead for brush to accumulate.
  • 12 rows of 1 ¼" high coarse teeth on roller to pull brush in.
  • 3 position control bar on feed hopper - forward, neutral & reverse.
  • The Mitts & Merrill hydraulic system is also equipped with a feed roll control sensor. When this sensor is engaged and the RPM of the motor slows by 400 RPM’s or more (due to chipping 6" - 8" diameter logs), the sensor automatically stops the feed roller, until the engine returns to its normal RPM’s.
  • Overall Dimensions: 14' 7" Long x 6' 3" Wide x 7' 11" High.

Optional Equipment:

  • Feed Chute folds to enclose the cutter chamber during storage or transportation. It is side hinged so it may be swung to either side for easy access to cutter chamber.
  • California Style One Piece discharge chute with 360 degree swivel deflector (bonnet). Available for 12" and 16" machines.

WARRANTY - FORD ENGINES

Engine - Internal parts (Crank, cylinder head, pistons, etc.*) by FORD - Limited 2 Years or
2000 Hours whichever comes first. *The warranty applies to certain listed components.
For a complete list - see warranty sheet provided with your machine.

Engine - External parts by FORD - 1 Year or 2000 Hours whichever comes first.

The warranty shall not apply to misapplication, abuse, misuse, or negligence. The engine shall be properly operated and maintained in accordance with Power Products Owner/Operators Manual for the engine provided with chipper.

Chipper Parts - Other than engine - 1 Year.

Factory will advise terms of warranty if other than FORD Engine is ordered for new chipper.

This company reserves the right to change the list price of chipper products without notice.
It shall have the right to discontinue the manufacture of any model or type of products, and change the design or add improvements at any time without incurring any obligation to install the same on MITTS & MERRILL BRUSH CHIPPERS previously purchased.